E014 · Source-scoped pinout variants

DVI-D dual-link connector engineering reference

Numbered grid positions only; flat blade excluded from this count. The full DDWG Rev. 1.0 interface table is represented; exact product wiring can leave positions unused.

Open field note Source trail

Source checked · no independent review claimed · Fabrication approved: no

DVI-D dual-link connector — scoped DVI reference original orientation schematic — Original pinout diagram; read the exact variant and view below. Not to scale.

Contact count

24

Numbered grid positions only; flat blade excluded from this count.

Mating boundary

Shape is not the verdict.

Match the exact DVI variant and analog contact area without force. Physical fit does not prove active links, analog support or converter direction.

source-scoped contact reference · independent review pending

Read the contact side, not a guessed mirror

This pilot uses the documented view for DDWG DVI-D dual-link receptacle reference. It is not a general pinout, device compatibility check, wiring instruction or fabrication drawing.

Only the numbered 24-position digital grid is located. Blade geometry, shields, exact pad spacing and housing dimensions are deliberately not drawn.

Source scopeDVI Revision 1.0 · 1999-04-02

Reading directionReceptacle front / mating side

Contact mappingNumbered layout, within exact cited view

Verify next: For a plug/front or rear-termination view, use the corresponding DDWG source figure; never mirror this grid by assumption.

Show source locator, claim and unresolved limitations

C014B · open this page’s canonical claim — DDWG DVI 1.0 Table 5-1 defines 24 numbered digital-only positions. Pin 8 is not connected in that table; positions 4/5, 12/13 and 20/21 carry the additional TMDS data pairs.

S411 · Digital Display Working Group (DDWG) / source register · Read original source ↗

Source location: Printed/PDF pp. 43–47; Tables 5-1 and 5-2; Figures 5-1, 5-3 and 5-5.

Limitations: Mirror hosting is not an official live DDWG publication channel. No independent authentication, fabrication approval, current product conformance, universal PCB layout or timing guarantee.

Profile unknowns: The flat digital blade is not an invented numbered signal 25. Different vendor counts can include or exclude it.

Rights: Original bounded factual paraphrase and links only. No source PDFs, artwork or logos redistributed. The indexed schematic is original, not a tracing of the source drawing.

Source-scoped reference · No independent technical or rights certification claimed · Physical fit, polarity, voltage and device modes: not inferred.

Orientation

How to read this profile

DDWG Rev. 1.0 Tables 5-1/5-2 and Figures 5-1/5-3; receptacle viewed from its mating front, numbered grid on the left, position 1 upper-left and position 24 lower-right. The plug front is mirrored (Figure 5-5). Molex explicitly labels its combined diagram as a receptacle front view. Not a solder-side or PCB map.

Source-scoped identification facts

Each value retains its exact example, role and measurement axis. Facts from different parts must not be combined into an invented component.

Documented examples; not a mating drawing or compatibility approval
Nominal contacts	24S411 · S413 · S414Numbered grid positions only; flat blade excluded from this count.; nominal engineering count, not automatically positions, population or a device wiring map. Numbered grid positions only; flat blade excluded from this count.
Positions / cavity span	24 (Claim C014C)S413Recorded source-scoped values; named examples do not describe every family variant or establish compatibility. Exact manual table, page 44. Other source-specific labels remain separate from the DDWG table.
Contact rows	3 (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
Contact pitch	1.9 mm manufacturer-reported centerline or mating-interface pitch (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
Dimensions / axis	2.34 mm PCB tail length (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
Connector role	socket (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
Keying / polarization	manufacturer reports keyed and polarized to mating part (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
Manufacturer	Molex (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
Series	74320 DVI digital (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
Exact part / implementation	74320-4004 (74320-4004)S866 · S873Separate exact examples; retain each value’s source, role, axis and part scope. Exact named example 74320-4004: DVI digital right-angle receptacle. Exact example only; no universal geometry, electrical compatibility, fabrication approval or wiring instruction. 1.90mm is the current part-page mating-interface value as displayed; source drawing refers users to DDWG for mating dimensions. No unobserved diagram dimension is interpreted.
View convention	DDWG Rev. 1.0 Tables 5-1/5-2 and Figures 5-1/5-3; receptacle viewed from its mating front, numbered grid on the left, position 1 upper-left and position 24 lower-right. The plug front is mirrored (Figure 5-5). Molex explicitly labels its combined diagram as a receptacle front view. Not a solder-side or PCB map.S411 · S413 · S414Recorded source-scoped values; named examples do not describe every family variant or establish compatibility. Existing engineering orientation text; source/part/view remains controlling.

Not recorded: Populated contacts, Contact gender / arrangement, Mounting, Coupling / latch, Shell / form, Recorded markings. Unknown fields stay unknown; illustrations supply no measurements or pin assignments.

Recorded variant and source limits

The flat digital blade is not an invented numbered signal 25. Different vendor counts can include or exclude it.
No housing dimensions, tolerances, insertion depth, PCB layout or fabrication approval is established.
Full receptacle contact presence is not evidence that a source, cable or receiver operates both links.
Do not apply voltage or modify connector pins based on a reference table. Exact device wiring and operating requirements remain separate.
DVI 1.0 digital-only connector, all 24 contacts (both TMDS links): Receptacle mating face, pin 1 upper left (Figure 5-1).
DDWG DVI 1.0 digital-only connector (Table 5-1), both TMDS links: DDWG DVI 1.0 Fig. 5-1 (p. 45), receptacle mating face: pin 1 top-left; pins 1-8 top row, 9-16 middle row, 17-24 bottom row, left to right; pin 24 bottom-right; flat-blade / micro-cross area to the right. Fig. 5-5 (p. 47) shows the plug face mirrored: pin 1 top-right, blade on the left.

Report a correction to these facts →

Pins & wiring

Pinout

Choose the exact wiring. Pin numbers follow its stated view; a schematic does not establish physical positions. Check your exact device before wiring.

Dark pinout view

What the status labels mean

Confirmed: Recorded research passes agree within this variant; this is not independent human review or hardware validation.
Single source: Only one underlying document, or one pass, supports this assignment.
Device-specific: Supported for the named equipment or wiring only. Check your device’s manual.
Unverified: Missing or conflicting evidence. Do not wire from this row.
Not connected: The source explicitly says NC, no contact or no pin for this wiring.

Wiring variantDVI 1.0 digital-only connector, all 24 contacts (both TMDS links)

DVI 1.0 digital-only connector, all 24 contacts (both TMDS links)

View and evidence limits

Receptacle mating face, pin 1 upper left (Figure 5-1).

P014 DVI-D dual-link — **Agree** on all 24 contacts — DDWG DVI 1.0 only; neither pass found an independent second source.
No named dual-link device or cable document was examined; rows reflect the DVI 1.0 connector table, corroborated by Molex PS-74320-001.

Schematic only · physical contact positions unconfirmed. Original drawing · not to scale. Scroll sideways if needed.

DVI 1.0 digital-only connector, all 24 contacts (both TMDS links) — source-scoped contact map
Pin	Signal	What it does	Status
1	T.M.D.S. Data2-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
2	T.M.D.S. Data2+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
3	T.M.D.S. Data2/4 Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
4	T.M.D.S. Data4-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
5	T.M.D.S. Data4+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
6	DDC Clock	Clock or clock-control connection, as named by this source.	Single source Sources
7	DDC Data	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
8	No Connect	Not connected or absent in this named wiring.	Not connected Sources
9	T.M.D.S. Data1-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
10	T.M.D.S. Data1+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
11	T.M.D.S. Data1/3 Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
12	T.M.D.S. Data3-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
13	T.M.D.S. Data3+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
14	+5V Power	Power connection (+5V Power). Check the specified supply.	Single source Sources
15	Ground (for +5V)	Ground reference and return.	Single source Sources
16	Hot Plug Detect	Control, detection or configuration connection; check the source and device.	Single source Sources
17	T.M.D.S. Data0-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
18	T.M.D.S. Data0+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
19	T.M.D.S. Data0/5 Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
20	T.M.D.S. Data5-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
21	T.M.D.S. Data5+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
22	T.M.D.S. Clock Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
23	T.M.D.S. Clock+	Clock or clock-control connection, as named by this source.	Single source Sources
24	T.M.D.S. Clock-	Clock or clock-control connection, as named by this source.	Single source Sources

Sources (4)

S683 · Digital Display Working Group (DDWG) · Digital Visual Interface (DVI)
Revision 1.0, 02 April 1999 · Section 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Section 2.6 Signal List (signal descriptions), p. 23 of 76
S688 · Molex · MicroCross - DVI I/O Plug and Receptacle Connector System, Product Specification PS-74320-001
Rev. J (revision block: EC# T2003-0134, dated 02/11/22); distributor-hosted copy of the Molex document · Sheet 2 of 17, Table 1 Digital-Only Connector Pin Assignments (stated source: DVI Specification Revision 1.0)
S686 · Digital Display Working Group (DDWG) · Digital Visual Interface (DVI)
Revision 1.0, 02 April 1999 · Sec. 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Sec. 2.6 Signal List (signal descriptions, link/channel mapping), p. 23 of 76
S687 · Digital Display Working Group (document hosted by Molex via TTI) · Digital Display Working Group Delivers DVI (summary sheet)
Undated two-page summary; references DVI 1.0 · p. 2, 'Digital Only Connector' pin/signal table

DDWG DVI 1.0 digital-only connector (Table 5-1), both TMDS links

View and evidence limits

DDWG DVI 1.0 Fig. 5-1 (p. 45), receptacle mating face: pin 1 top-left; pins 1-8 top row, 9-16 middle row, 17-24 bottom row, left to right; pin 24 bottom-right; flat-blade / micro-cross area to the right. Fig. 5-5 (p. 47) shows the plug face mirrored: pin 1 top-right, blade on the left.

P014 DVI-D dual-link — **Agree** on all 24 contacts — DDWG DVI 1.0 only; neither pass found an independent second source.
Both links share one clock pair (Sec. 2.2.2, p. 12).
Every row rests on DDWG documents only. The Molex-hosted summary comes from the same publisher. No dual-link DVI-D device manual from another publisher was obtained (Dell U3011/U2711/3008WFP guide downloads failed or returned 404).

Schematic only · physical contact positions unconfirmed. Original drawing · not to scale. Scroll sideways if needed.

DDWG DVI 1.0 digital-only connector (Table 5-1), both TMDS links — source-scoped contact map
Pin	Signal	What it does	Status
1	T.M.D.S. Data2-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
2	T.M.D.S. Data2+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
3	T.M.D.S. Data2/4 Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
4	T.M.D.S. Data4-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
5	T.M.D.S. Data4+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
6	DDC Clock	Clock or clock-control connection, as named by this source.	Single source Sources
7	DDC Data	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
8	No Connect	Not connected or absent in this named wiring.	Not connected Sources
9	T.M.D.S. Data1-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
10	T.M.D.S. Data1+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
11	T.M.D.S. Data1/3 Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
12	T.M.D.S. Data3-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
13	T.M.D.S. Data3+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
14	+5V Power	Power connection (+5V Power). Check the specified supply.	Single source Sources
15	Ground (for +5V)	Ground reference and return.	Single source Sources
16	Hot Plug Detect	Control, detection or configuration connection; check the source and device.	Single source Sources
17	T.M.D.S. Data0-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
18	T.M.D.S. Data0+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
19	T.M.D.S. Data0/5 Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
20	T.M.D.S. Data5-	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
21	T.M.D.S. Data5+	Signal conductor. Pair, polarity and direction follow this named wiring.	Single source Sources
22	T.M.D.S. Clock Shield	Cable screen or shield connection; check the named equipment.	Single source Sources
23	T.M.D.S. Clock+	Clock or clock-control connection, as named by this source.	Single source Sources
24	T.M.D.S. Clock-	Clock or clock-control connection, as named by this source.	Single source Sources

Sources (4)

S686 · Digital Display Working Group (DDWG) · Digital Visual Interface (DVI)
Revision 1.0, 02 April 1999 · Sec. 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Sec. 2.6 Signal List (signal descriptions, link/channel mapping), p. 23 of 76
S687 · Digital Display Working Group (document hosted by Molex via TTI) · Digital Display Working Group Delivers DVI (summary sheet)
Undated two-page summary; references DVI 1.0 · p. 2, 'Digital Only Connector' pin/signal table
S683 · Digital Display Working Group (DDWG) · Digital Visual Interface (DVI)
Revision 1.0, 02 April 1999 · Section 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Section 2.6 Signal List (signal descriptions), p. 23 of 76
S688 · Molex · MicroCross - DVI I/O Plug and Receptacle Connector System, Product Specification PS-74320-001
Rev. J (revision block: EC# T2003-0134, dated 02/11/22); distributor-hosted copy of the Molex document · Sheet 2 of 17, Table 1 Digital-Only Connector Pin Assignments (stated source: DVI Specification Revision 1.0)

Unknowns stay unknown.

The flat digital blade is not an invented numbered signal 25. Different vendor counts can include or exclude it.
No housing dimensions, tolerances, insertion depth, PCB layout or fabrication approval is established.
Full receptacle contact presence is not evidence that a source, cable or receiver operates both links.
Do not apply voltage or modify connector pins based on a reference table. Exact device wiring and operating requirements remain separate.

Your next step

Use the detail without guessing past its limits.

Read the connector field note Recognition clues and practical checks.Work through a connection Keep exact equipment and cable requirements separate.

Source trail

Claims and sources

C014Bsource checked

DDWG DVI 1.0 Table 5-1 defines 24 numbered digital-only positions. Pin 8 is not connected in that table; positions 4/5, 12/13 and 20/21 carry the additional TMDS data pairs.

Digital Display Working Group (DDWG) · Digital Visual Interface, Revision 1.0 (02 April 1999) ↗
Printed/PDF pp. 43–47; Tables 5-1 and 5-2; Figures 5-1, 5-3 and 5-5. · Mirror hosting is not an official live DDWG publication channel. No independent authentication, fabrication approval, current product conformance, universal PCB layout or timing guarantee.

C014Csource checked

Dell SE2416HM documentation shows a numbered 24-position DVI-D grid but labels positions 4, 5, 12, 13, 20 and 21 Floating. Its implementation must not be substituted into a universal dual-link pinout.

Dell · SE2416HM Monitor User’s Guide — DVI-D connector assignments ↗
PDF/printed p. 44: numbered DVI-D view and 24-position assignment table. · Labels belong to this manual. Do not substitute its Self test or supply labels for the DDWG standard; no voltage application, hardware measurement, or universal DVI implementation is established.

C014Dsource checked

Dell documents E-Port docks with DVI connectors accepting dual-link-shaped cables but wired for single-link operation. It also identifies the source, cable, display and any adapter as separate dual-link requirements.

Dell · Video Display and Multiple Video Display General Information — DVI questions ↗
Article 000052929, version 13; modified 17 April 2026. First FAQ on dual link, E-Port dock note, and active/passive adapter definitions. · General article includes simplified descriptions and a broad conversion chart; those are not adopted as universal compatibility rules. E-Port wording is not an inventory of every dock revision.

C801Msource checked

DVI 1.0 digital-only connector, all 24 contacts (both TMDS links): original contact normalization. Statuses distinguish comparison agreement, source limits and named-device wiring.

Digital Display Working Group (DDWG) · Digital Visual Interface (DVI) ↗
Section 2.6 Signal List (signal descriptions), p. 23 of 76; Section 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Section 5.2.1.2, Table 5-2 Combined Analog and Digital Connector Pin Assignments, p. 44 of 76; Section 5.2.6.1, Figure 5-6 Analog Plug Connector Mating Interface Dimensions, p. 47 of 76; Sections 2.2.2.1-2.2.2.2 T.M.D.S. Link System/Monitor Requirements, p. 13 of 76 · Source scope and unresolved evidence are preserved in the engineering variant. Recorded original location/access note: http://www.ddwg.org/lib/dvi_10.pdf (retrieved from Internet Archive capture https://web.archive.org/web/20060630104414/http://www.ddwg.org:80/lib/dvi_10.pdf; ddwg.org no longer serves it)

Digital Display Working Group (DDWG) · Digital Visual Interface (DVI) ↗
Fig. 5-1 Digital-only Receptacle Connector Mating Interface Dimensions, p. 45 of 76; Sec. 2.2.2, Table 2-1 Single and Dual Link Operation and Sec. 2.2.2.1-2.2.2.2 link requirements, pp. 12-13 of 76; Sec. 2.6 Signal List (signal descriptions, link/channel mapping), p. 23 of 76; Sec. 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Sec. 5.2.1.2, Table 5-2 Combined Analog and Digital Connector Pin Assignments, p. 44 of 76; Sec. 5.2.6.1, Fig. 5-6 Analog Plug Connector Mating Interface Dimensions, p. 47 of 76 · Source scope and unresolved evidence are preserved in the engineering variant.

Digital Display Working Group (document hosted by Molex via TTI) · Digital Display Working Group Delivers DVI (summary sheet) ↗
p. 2, 'Combined Connector (with micro-cross)' pin/signal table; p. 2, 'Digital Only Connector' pin/signal table · Source scope and unresolved evidence are preserved in the engineering variant.

Molex · MicroCross - DVI I/O Plug and Receptacle Connector System, Product Specification PS-74320-001 ↗
Sheet 2 of 17, Table 1 Digital-Only Connector Pin Assignments (stated source: DVI Specification Revision 1.0); Sheet 3 of 17, Table 2 Combined Analog and Digital Connector Pin Assignments (stated source: DVI Revision 1.0) · Source scope and unresolved evidence are preserved in the engineering variant.

C801Nsource checked

DDWG DVI 1.0 digital-only connector (Table 5-1), both TMDS links: original contact normalization. Statuses distinguish comparison agreement, source limits and named-device wiring.

7 source records support this profile. No independent engineering review or hardware validation is claimed.

Evidence behind this page

Scope first. Source second. Approval separate.

7 linked sources · 5 scoped claims · 0 sources with inspection/access flags.

Page scope: No new drawing. Existing original unnumbered artwork remains an identification illustration, not the numbered source view.

Assessment 2026-10-22 · earliest scheduled source review 2027-01-05. This is a recorded-date assessment, not a live source check. Page-level independent review is not established by this panel.

Inspect 7 source scopes, access limits and dates

S411 · Digital Visual Interface, Revision 1.0 (02 April 1999)

Digital Display Working Group (DDWG) · Unclassified publisher domain · inspected 2026-10-07 · due 2027-01-05

Within inspection window

Scoped support: Primary DDWG specification authored in 1999, read from an explicitly third-party document mirror. Digital-only and combined assignments, interface grouping and numbered receptacle/plug views.

Not established / limitations: Mirror hosting is not an official live DDWG publication channel. No independent authentication, fabrication approval, current product conformance, universal PCB layout or timing guarantee.

Locator: Printed/PDF pp. 43–47; Tables 5-1 and 5-2; Figures 5-1, 5-3 and 5-5.

S413 · SE2416HM Monitor User’s Guide — DVI-D connector assignments

Dell · Manufacturer / product-owner domain · inspected 2026-10-07 · due 2027-01-05

Within inspection window

Scoped support: Exact SE2416HM manual example. Positions 4, 5, 12, 13, 20 and 21 are labeled Floating despite the full numbered grid.

Not established / limitations: Labels belong to this manual. Do not substitute its Self test or supply labels for the DDWG standard; no voltage application, hardware measurement, or universal DVI implementation is established.

Locator: PDF/printed p. 44: numbered DVI-D view and 24-position assignment table.

S414 · Video Display and Multiple Video Display General Information — DVI questions

Dell · Manufacturer / product-owner domain · inspected 2026-10-07 · due 2027-01-05

Within inspection window

Scoped support: Bounded use: 18 versus 24 grid positions; source/cable/display requirements; named E-Port single-link wiring despite accepting dual-link-shaped cables; active versus passive circuitry.

Not established / limitations: General article includes simplified descriptions and a broad conversion chart; those are not adopted as universal compatibility rules. E-Port wording is not an inventory of every dock revision.

Locator: Article 000052929, version 13; modified 17 April 2026. First FAQ on dual link, E-Port dock note, and active/passive adapter definitions.

S683 · Digital Visual Interface (DVI)

Digital Display Working Group (DDWG) · Unclassified publisher domain · inspected 2026-10-20 · due 2027-01-18

Within inspection window

Scoped support: Exact named pinout variant only; not capability or compatibility approval.

Not established / limitations: Source scope and unresolved evidence are preserved in the engineering variant. Recorded original location/access note: http://www.ddwg.org/lib/dvi_10.pdf (retrieved from Internet Archive capture https://web.archive.org/web/20060630104414/http://www.ddwg.org:80/lib/dvi_10.pdf; ddwg.org no longer serves it)

Locator: Section 2.6 Signal List (signal descriptions), p. 23 of 76; Section 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Section 5.2.1.2, Table 5-2 Combined Analog and Digital Connector Pin Assignments, p. 44 of 76; Section 5.2.6.1, Figure 5-6 Analog Plug Connector Mating Interface Dimensions, p. 47 of 76; Sections 2.2.2.1-2.2.2.2 T.M.D.S. Link System/Monitor Requirements, p. 13 of 76

S686 · Digital Visual Interface (DVI)

Digital Display Working Group (DDWG) · Unclassified publisher domain · inspected 2026-10-20 · due 2027-01-18

Within inspection window

Scoped support: Exact named pinout variant only; not capability or compatibility approval.

Not established / limitations: Source scope and unresolved evidence are preserved in the engineering variant.

Locator: Fig. 5-1 Digital-only Receptacle Connector Mating Interface Dimensions, p. 45 of 76; Sec. 2.2.2, Table 2-1 Single and Dual Link Operation and Sec. 2.2.2.1-2.2.2.2 link requirements, pp. 12-13 of 76; Sec. 2.6 Signal List (signal descriptions, link/channel mapping), p. 23 of 76; Sec. 5.2.1.1, Table 5-1 Digital-Only Connector Pin Assignments, p. 43 of 76; Sec. 5.2.1.2, Table 5-2 Combined Analog and Digital Connector Pin Assignments, p. 44 of 76; Sec. 5.2.6.1, Fig. 5-6 Analog Plug Connector Mating Interface Dimensions, p. 47 of 76

S687 · Digital Display Working Group Delivers DVI (summary sheet)

Digital Display Working Group (document hosted by Molex via TTI) · Unclassified publisher domain · inspected 2026-10-20 · due 2027-01-18

Within inspection window

Scoped support: Exact named pinout variant only; not capability or compatibility approval.

Not established / limitations: Source scope and unresolved evidence are preserved in the engineering variant.

Locator: p. 2, 'Combined Connector (with micro-cross)' pin/signal table; p. 2, 'Digital Only Connector' pin/signal table

S688 · MicroCross - DVI I/O Plug and Receptacle Connector System, Product Specification PS-74320-001

Molex · Unclassified publisher domain · inspected 2026-10-20 · due 2027-01-18

Within inspection window

Scoped support: Exact named pinout variant only; not capability or compatibility approval.

Not established / limitations: Source scope and unresolved evidence are preserved in the engineering variant.

Locator: Sheet 2 of 17, Table 1 Digital-Only Connector Pin Assignments (stated source: DVI Specification Revision 1.0); Sheet 3 of 17, Table 2 Combined Analog and Digital Connector Pin Assignments (stated source: DVI Revision 1.0)

Trace 5 claims to their source records

C014B · P014

DDWG DVI 1.0 Table 5-1 defines 24 numbered digital-only positions. Pin 8 is not connected in that table; positions 4/5, 12/13 and 20/21 carry the additional TMDS data pairs.

Claim scope: Full digital-only interface assignment from the named specification; not a guarantee that an exact device implements every signal.

Source links: S411 · Evidence trail → (private workspace)

C014C · P014

Claim scope: Exact manual table, page 44. Other source-specific labels remain separate from the DDWG table.

Source links: S413 · Evidence trail → (private workspace)

C014D · P014

Claim scope: Named legacy dock example and documentation checklist, not a universal resolution limit or all-dock inventory.

Source links: S414 · Evidence trail → (private workspace)

C801M · P014

DVI 1.0 digital-only connector, all 24 contacts (both TMDS links): original contact normalization. Statuses distinguish comparison agreement, source limits and named-device wiring.

Claim scope: Pinout variant only; see comparison and per-contact status. Not fabrication approval.

Source links: S683 · S686 · S687 · S688 · Evidence trail → (private workspace)

C801N · P014

DDWG DVI 1.0 digital-only connector (Table 5-1), both TMDS links: original contact normalization. Statuses distinguish comparison agreement, source limits and named-device wiring.

Claim scope: Pinout variant only; see comparison and per-contact status. Not fabrication approval.

Source links: S683 · S686 · S687 · S688 · Evidence trail → (private workspace)

Prepare this page for review →Read the evidence method →

Recorded evidence only. An inspection date, publisher label, source link or generated packet is not independent technical review, hardware testing, fabrication approval or a compatibility verdict.